LDDL2-05电磁离合器

焦作制动器控股集团有限公司
中国重型机械总公司
焦作制动器厂
销售电话 15239003005  0391-7543530

规格Specifications 数据Contents	LDDL2 -05	LDDL2 -10	LDDL2 -20	LDDL2 -40	LDDL2 -80	LDDL2 -160	LDDL2 -250	LDDL2 -320	LDDL2 -500	LDDL2 -1000
额定力矩(N.m) Rated Braking Torque	6	10	20	40	80	160	250	320	500	1000
额定功率P20℃(W) Rated Power	12	15	20	25	35	45	55	60	80	100
额定电压(V dc) Rated Voltage	24	24	24	24	24	24	24	24	24	24
接通时间(ms) Connecting Time T1	55	75	120	140	230	250	303	380	450	505
断开时间(ms) Disconnecting Time T2	15	25	35	45	60	90	170	200	260	330
允许最高工作转速(rpm) Allowable Max Speed	3600	3600	3000	3000	2500	2500	2500	2000	2000	1500

三、外形及安装尺寸（Overall and lnstallation Dimensions）

尺寸Size 规格Specifications	D1	D2	D3	D4	D5	D6	D7	D8	D9	M	d	L	L1	L2	L3	L4	L5	L6	L7	b	b1	h	δ
LDDL2-05	80	72	35	67	46	38	12	4x5	3x3.1	M4	15	24	4	19	27.5	20	22	15	14	4	4	13.8	0.3
LDDL2-10	100	90	42	85	60	45	15	4x6	3x4.1	M5	15	26	5	25	35	25	24	20	15	5	5	17.3	0.3
LDDL2-20	125	112	52	106	76	55	20	4x7	3x5.2	M5	20	30	6	31	41	30	27	25	20	6	6	22.3	0.4
LDDL2-40	150	137	62	133	95	64	25	4x7	3x6.2	M6	25	34	6.5	36.5	52.5	40	30	30	30	8	8	28.3	0.4
LDDL2-80	190	175	80	169	120	75	30	4x9.5	3x8.2	M8	30	38	8.5	47	65.5	50	34	38	35	8	8	33.3	0.5
LDDL2-160	230	215	100	213	158	100	45	4x9.5	3x10.2	M8	45	44	11	53	80	60	40	42	45	14	14	48.8	0.5
LDDL2-250	280	260	120	253	185	110	50	4x11	3x10.2	M10	55	50	12	62	81.5	65	45	50	50	16	16	59.3	0.6
LDDL2-320	290	270	120	267	210	118	45	4x11	3x12.2	M10	55	51	12.5	67.5	92.5	70	47	55	50	16	16	59.3	0.6
LDDL2-500	310	290	130	285	248	125	50	4x11	4x12.2	M10	60	55	13.5	73.5	99.5	75	50	60	55	18	16	64.4	0.8
LDDL2-1000	440	420	200	424	315			4x12.5	4x16.2	M12	70	66	19	95			56	76		20		74.9	0.8

四、安装（Installation）
安装注意事项 Warning
●摩擦片及衔铁表面不得有油污，必须保持清洁；
Friction disc and armature surface should be kept clean and free of grease.
●安装离合器必须保证同轴度不大于0.1mm；
The coaxial degree should not exceed 0.1mm.
●与离合器配合的轴孔与轴精密度为H8/h7
Fit h7 is recommended so that the brake can be fitted easily and without demange on to the shaft.
●离合器主、从动侧需固定，不允许有轴向窜动，同时必须保证工作气隙“δ”
Not allowed to move on axial direction. Airgap should be kept in “δ”.